I am truly want to know why is my Amana washer not agitating. It is embarrassing and also worrying when you run the wash cycle but the washer won’t agitate properly, right?
Do you know it probably happens due to a malfunctioning lid switch, door latch assembly, damaged drive belt, motor, coupling, or agitator?
To fix this issue, you may need to check these parts and address the exact causes, and replace or repair them if necessary.
We are exactly here to teach you address the exact reasons why is your amana washer not agitating and the way you can try to fix this issue yourself.
Why is my amana washer not agitating properly: How to fix it?
If your Amana washer is not agitating, there could be several possible reasons for this issue. Below are some common causes and steps to fix each problem:
Lid Switch Malfunction: for top load washer
The lid switch is a safety feature of the washer. It prevents the washer from agitating when the lid is open. If the lid switch is faulty or not engaging properly, it can interrupt the agitating cycle.
How to fix it:
- Check if the lid is closing completely. If it’s not, adjust the position or replace the lid if damaged.
- Locate the lid switch (usually located near the lid hinge).
- Now test it for continuity using a multimeter.
- If there’s no continuity when the lid is closed, the switch may be faulty and needs to be replaced.
To replace the lid switch on an Amana washer, read our other post here.
Drive Belt Issue:
If the drive belt that connects the motor to the transmission is damaged or broken, the washer won’t agitate.
When the motor rotates, it transfers power through the drive belt to move the agitator back and forth.
How to fix it:
- Unplug the washer and access the back panel or the bottom of the washer.
- Inspect the drive belt for signs of wear, cracks, or damage. If it’s damaged, replace the belt with a new one.
How to replace a drive belt?
To replace the drive belt, follow the below steps carefully:
- Unplug the washer.
- Use a wrench or screwdriver to release tension on the belt by loosening the tensioner or moving the motor.
- Slide the old drive belt off the pulleys and transmission. Take note of the belt’s routing before removal to aid in installing the new one correctly.
- Place the new drive belt onto the pulleys and transmission, following the same routing as the old belt.
- Adjust the belt tension by tightening the tensioner or moving the motor back to its original position.
- Manually rotate the drum to check that the belt is properly aligned and seated.
- Now put back the front or rear panel of the washer and secure it in place.
- Plug in the washer.
Motor Problems:
A malfunctioning motor can also lead to the agitator not working. The motor is the heart of the washing machine.
It provides the power required for various functions, including agitating the clothes.
How to fix it:
- Check for any visible signs of damage or burning on the motor.
- Test the motor using a multimeter to see if it’s receiving power and if it’s operating as it should. If it is faulty, it will need to be replaced.
Agitator Dogs (Cogs) Worn Out:
Many top-load washers have agitator dogs. These are small plastic cogs that engage the agitator and facilitate its movement.
Over time, these cogs can wear out and cause the agitator to stop working.
How to fix it?
a. Remove the fabric softener dispenser or cap from the top of the agitator.
b. Remove the agitator bolt or nut, depending on the model.
c. Lift the agitator out of the washer.
d. Check the agitator dogs for wear. If they are worn or damaged, replace them with new ones.
e. Reassemble the agitator and reinstall it in the washer.
Amana washer agitator loose:
A loose agitator may not be able to move and agitate the clothes properly. As a result, your laundry might not get cleaned thoroughly.
In some cases, if the agitator is very loose and not secured properly, it could completely detach from its mounting.
This can cause damage to the washer’s internal components or even damage the agitator itself.
How to fix it?
To fix this issue, you need to tighten the loose agitator. Follow the below steps to do it:
- Check for bolts or screws holding the agitator to the shaft. Tighten them securely if loose.
- Some Amana washers use agitator dogs or cogs to facilitate the agitating action. Inspect these agitator dogs (cogs) and replace them if worn out.
- The agitator splines are grooves or ridges inside the agitator. It fits onto the corresponding splines of the agitator shaft. Verify agitator splines for wear or damage and replace them if necessary.
- For dual-action agitators, tighten the mounting bolt connecting the upper and lower components.
Agitator Coupling/Coupler:
The agitator coupling or coupler is the part that connects the agitator to the transmission shaft. If it becomes damaged or worn out, the agitator won’t be able to function correctly.
How to fix it?
- You’ll need to inspect the agitator coupling and replace it if it shows signs of wear or damage.
- Replacing the coupling will restore the connection between the agitator and the transmission shaft.
Amana Washer Agitator Repair Kit:
Some Amana washers have specific agitator repair kits available. These kits contain all the necessary components to address agitator-related issues. Such as worn-out parts or loose connections.
What to do?
Purchase the appropriate agitator repair kit for your model. Follow the provided instructions in the kit to complete the repair.
Control Board Issue:
control board regulates the washer’s functions. If it malfunctions, it may affect the agitator’s operation.
What to do?
Inspect the control board for any visible signs of damage, such as burnt areas or loose connections.
If you suspect a control board issue, contact a qualified appliance technician to diagnose and repair the problem. They may need to replace the faulty control board.
Amana top load washer not agitating:
Most of the causes for your top loader not agitating are the same as we have already learned above.
Basically, your top-load amana washer may not work if the lid lock switch is not closed properly. Even if it is defective, the washer won’t agitate or spin. To troubleshoot this condition you may reset the lid lock of Amana washer
In addition, worn-out agitator components also cause the washer to not agitate properly. A damaged transmission drive block and a worn drive motor are also responsible for this issue.
How to fix a top load washer not agitating?
You should first address the main cause of your washer not agitating. Then take some steps to resolve this issue.
Check the above parts of the washer and if they are defective or worn out, replace them if needed to solve this issue.
Amana washer won’t agitate or spin:
Your amana washer may not agitate or spin if the drive motor is faulty. It means no power is reaching the washer drive motor. If so, replace the motor with a new one.
Also, check the drive belt. Replace it if necessary.
Then, look at the door latch assembly on the front load washer or lid switch for the top loader washer. Replace them if necessary.
You may also need to replace the timer or control board. If these amana washer parts are defective, your washer won’t agitate or spin.
A faulty capacitor can also affect the motor’s performance and, in turn, affect agitation and spinning.
Washer not agitating but spinning: what to do?
When your washer is not agitating but is still spinning, you can try the below checking and fixing method:
A broken agitator will be the main cause of not agitating your amana washer but spinning.
Open the washer and check the agitator components, such as agitator dogs or cogs. These parts can wear out over time and may need to replace the Amana washer agitator if they are damaged.
A malfunctioning transmission can also lead to a lack of agitation. Inspect the transmission for any visible problems or unusual noises. If the transmission is faulty, it may require repair or replacement.
Even the faulty drive motor, lid switch, or timer also causes this issue. So check and replace these parts if needed.
Final word:
We hope this article has covered all the issues that cause your Amana washer not to agitate.
To fix this issue, follow our article and check the Amana washer agitator, drive belt, lid switch, drive motor, or other mentioned parts.
If they seem to be damaged or defective, replace them.
Obviously, you should unplug your washer before attempting any checking or repairing. If necessary, don’t hesitate to call a technician.
Leave a Reply