How To Replace A Drain Pump On A Kenmore Washer

A washing machine drain pump is one of the essential components of the appliance. It is responsible for draining water out of the machine during the wash and spin cycles. Over time, the drain pump may become worn out or faulty, which can result in issues with draining or water leakage.

In such cases, replacing the drain pump is necessary to restore the proper functioning of your washing machine. By following the steps outlined you will be able to replace the drain pump on your Kenmore washing machine with ease and efficiency.

How To Replace A Drain Pump On A Kenmore Washer

Looking to replace the drain pump on your Kenmore washing machine? Learn the step-by-step process for a seamless replacement to keep your machine running smoothly.

Shut off the power supply & Water: Before you begin any repairs, ensure that your washer is unplugged from the power source. This will prevent any accidents or electric shocks.

Locate the drain pump: The drain pump is typically located at the bottom of the washing machine. Refer to your owner’s manual or appliance diagram for specifics on the pump’s location.

Materials Needed:

• Manufacturer-approved replacement drain pump
• Work gloves
• Channel lock pliers
• Towel
• 3 bolts (for securing the new drain pump)

Step 1: Safety First Before you begin, ensure your safety. Wear work gloves to protect your hands. You may also want to have someone assist you in moving the washer away from the wall. Begin by unplugging the power cord from the wall outlet and turning off the water supply valves for the washer.

Step 2: Disconnecting Fill Hoses and Drain Hose

1. Pull the drain hose out of the standpipe behind the washer.
2. Carefully move the washer away from the wall so you can access the fill hoses and drain hose.
3. Mark which fill hose goes to the hot connector and which goes to the cold.
4. Using channel lock pliers, carefully loosen and remove both fill hoses. Be prepared for some water to spill out. Use a towel to wipe up any water spills to prevent slipping.

Step 3: Accessing the Drain Pump

1. Carefully tilt the washer forward and lay it on the front panel, so you can access the components from the bottom of the washer.
2. Use pliers to release the spring clamp on the drain hose.
3. Pull the drain hose off of the drain pump.
4. Open the cover that protects the wire harness plug on the drain pump.
5. Pull the wire harness plug out of the receptacle on the drain pump.

Step 4: Removing the Old Drain Pump

1. Remove the three bolts that secure the drain pump to the bottom of the washer tub.
2. Carefully pull the old pump off and set it aside for disposal.

Step 5: Installing the New Drain Pump

1. Position the new drain pump on the bottom of the washer and secure it using the three bolts.
2. Plug the wire harness into the receptacle on the new pump.
3. Close the cover on the wire harness connection.
4. Push the drain hose back onto the outlet of the drain pump and secure it with the spring clamp.

Step 6: Reconnecting Fill Hoses and Drain Hose

1. Carefully set the washer back in an upright position.
2. Move it close enough to the fill hoses so that you can reconnect them.
3. Thread the fill hoses onto the connections on the back of the washer.
4. Tighten the connections firmly using a pair of channel lock pliers.

Step 7: Final Steps

1. Put the drain hose back in place.
2. Turn on the water supply valves and check for any leaks. Tighten the connection if you find a slight leak.
3. Plug the washer into the electrical outlet.
4. Finally, return the washer to its original location.

By following these steps, you can replace the drain pump in your Kenmore Vertical Modular Washer (VMW) and get it back to working order.

Plug the washer back in: Once you have completed the installation of the new drain pump, plug your Kenmore washer back into the power source.

Test the washer: Turn on your washer and run a short cycle to check if the drain pump is functioning properly. Monitor the drainage to ensure there are no issues.

Credit: www.instructables.com

Conclusion

Replacing the drain pump on your Kenmore washing machine can significantly improve its performance and prolong its lifespan. By following the step-by-step instructions outlined in this blog post, you can easily replace the drain pump yourself and avoid the hassle and expense of hiring a professional.

Regular maintenance and timely replacement of worn-out parts like the drain pump are essential to ensure that your washing machine continues to function optimally. Remember to consult the user manual for specific instructions related to your Kenmore model and always prioritize safety by disconnecting the power supply before conducting any repairs.

By investing a little time and effort into DIY maintenance, you can save money and keep your Kenmore washing machine running smoothly for years to come. So go ahead, take charge of your appliance and say goodbye to clogged drains and frustrating laundry experiences!