Amana washer stuck on rinse cycle: 10 quick fixes to try

After loading and starting your washer, it begins the wash cycle normally.

But the problem is when it gets stuck on the rinse cycle and won’t go through the steps. What can you do in such cases?

You can check your water inlet valve, drain pump, main control board, water pressure, or timer to find any issues. 

If you suspect any issues, fix these by following our below troubleshooting steps.

One more said, don’t worry if your washer is stuck, skipping the rinse cycle as we are coming up with some quick troubleshooting guides you can try to solve your issues without a professional.

Why does my Amana washer stuck on rinse cycle?

Amana washer stuck on rinse cycle

Your Amana washer may mostly get stuck in the rinse cycle if there are any issues with the water inlet valve.

Yet, you can fix it with our below troubleshooting steps.

But before starting the troubleshooting process, you should first address and know the exact reason for this issue. 

We are including here some probable causes behind Amana washer won’t rinse and spin:

  1. The water inlet valve is defective.
  2. Power supply issues.
  3. The suspension rod is broken in the top load washer.
  4. The drain hose/pump may be clogged or faulty.
  5. The water flow is insufficient.
  6. The lid switch is defective in the Top load washer.
  7. The door lock is defective in the Front load washer.
  8. Problem with the timer.
  9. Problem with the main control board.

Note: Amana front load washer spin better and faster compared to the top loading washing machine

What to do if your Amana washer stops on the rinse cycle

It will be frustrating if your Amana washer gets stuck on the last rinse cycle.

But it will be solved if you follow and execute our troubleshooting tips suitably. We are here to help you.

We will include the solutions for your top or front-load washer. Let’s get started.

Solutions for Amana top loader washer not rinse

Check the lid switch

The lid switch prevents the washer from opening during the wash cycle. But if it isn’t closed properly, the washer keeps unlocking and won’t run properly.

  • So, check the lid switch.
  • Open and close the door firmly several times and try again.
  • If it is defective, reset amana lid switch or replace the switch.

Check for load balance

Check if you are packaging a large load in the washer. 

If yes, the clothes won’t move freely and cause the washer to not progress through a cycle.

  1. In such a case, pause the cycle, and open the lid.
  2. Take out some clothes or rearrange the items to ensure proper weight distribution.

If the problem still persists then read this: Amana washer not washing

Solutions for the top loader washing machine stuck on the rinse cycle

Check the door lock

The door lock of your front load washer does the same work as the top loader washer lid switch.

  • Check to confirm if the lock is faulty or not engaging properly. If yes, your washer won’t start the rinse cycle or cause the washer to get stuck in this step.
  • Check this door lock and latch to ensure they are in a good position and it is closing correctly.

Check for unbalanced load

check for unbalanced load

An overload or unbalanced load may cause your front load washer to get stuck in the rinse cycle. So,

  1. Pause the wash cycle, and redistribute the load evenly.
  1. Now resume the wash by pressing Start
  1. Ensure there are no heavy items on one side.

If the problem persists, then you can try Amana washer master reset

Troubleshoot for both top and front load washers

You can try out the below steps for both of your front or both load washers:

Check the Water inlet valve

  • The water inlet valve is responsible for transforming water into the washer tub. 
  • If it is clogged or blocked, the water transformation will fail, and the washer will be waiting for it. It ultimately causes the washer to stop at the rinse cycle. 
  • In that case, clean any dirt to back the valve work again.

Perform the following steps to clean the clogged or blocked valve:

  1. Unscrew the inlet valve from your washer. You will usually find it on the backside of the washer.
  1. Remove and clean any dirt or debris that might be present.
remove dirt or debris
  1. Flush the inlet valve with clean water.
  2. Secure the washer with the screws again.
  3. Now restart the rinse cycle.

Pro tips: Cleaning Amana washer is great stuff. Like, water inlet valve cleaning you should come to learn more about how to clean your Amana washer

  • Check the valve using a multimeter to identify any issues. If it has no continuity, it is defective. In that case, replace the valve.
multimeter test

Power supply issues

  • Check and ensure your washer is perfectly connected to a power source.
  • Check the power cord of your power supplier. If it is defective or loose, it can’t supply power. 
  • So you should correctly plug it into the grounded three-prong electrical outlet to confirm consistent electric power to your Amana washer.

Check the drain hose

  • If the drain hose doesn’t drain the water, the washer will stuck in the rinse cycle.
  • Check if it is faulty or clogged with any dirt. 
  • To do so, disconnect it and blow air through to confirm the complete flow. 
  • If yes, clean the drain pump, hose, or drain sink. Otherwise, it will activate the pressure switch and cause the washer to stop at the mid-cycle.
  •  Replace them if they are faulty. If the drain hose is kinked, straighten it to ensure easy water flow.

Check the water flow

  • Take out the water inlet pipe and observe the water flow rate at the source.
  • The minimum water pressure for the Amana washer water inlet valve is required 20 psi. It should be within 30 to 120 psi depending on the model
  • If the water pressure is less than 20 psi, this valve won’t flow the water properly.
  • It means an insufficient or low water pressure may cause the washer to get stuck in the rinse cycle.

Timer issue

The timer in your washer guides the control board on whether it is time to change the wash cycle. 

If the timer is deffective, it won’t act correctly and send signals to the control board. Then your control board can’t run the rinse cycle and cause your washer to get stuck on this cycle.

You will get the timer on the control panel or by releasing the back washer panel for some models.

Then you can test its continuity using a multimeter. If no continuity is seen, replace the washer timer. 

Malfunctioning of the main control board

Malfunctioning the main control board will be another reason to stop and get stuck in the washer during the rinse cycle. 

If your washer timer is well and sends signals, faulty control boards won’t receive these signals and work properly.

You can check it with a multimeter to identify any issues. If it doesn’t have continuity, replace it with a new one to fix the problem.

faulty control board

Electrical problems 

If your washer is stuck on the rinse cycle, electrical issues will be the root reason behind this. 

If the wiring is faulty, the timer will malfunction. 

control board wiring faulty

The burned-out or corroded wiring may prevent the timer from sending signals to the control board, and a cycle can’t go to the next step.

Even when your washer runs to the rinse cycle, power may be cut out and stop in this cycle.

  • It seems uneasy if you wish to fix this issue. So you should better search for professional help.

Also, the timer itself becomes faulty to cause this issue. You can go and read this article about timer replacement to replace it if needed.

Why my Amana washer won’t finish the rinse cycle?

There could be several reasons why your Amana washer won’t finish the rinse cycle. Such as
An unbalanced load, 
Clogged water inlet valve, 
Water supply issues, 
Faulty timer or control board, or sensor malfunctions. 

To troubleshoot these issues, Check Amana washer stuck on sensing fill troubleshooting to deeply understand and solve it.
For quick fix try troubleshooting steps:
Redistributing or rearranging the load.
Cleaning or replacing the water inlet valve. 
Ensuring proper water supply.
Replacing the faulty timer or control board.

Why my Amana washer won’t rinse and spin?

A clogged water pump filter will be the most probable cause if your washer won’t rinse or spin.
 Check if the filter is dirty or clogged. 
If yes, locate the drain hose pump at the bottom right back corner. Clean any dirt from the filter.
There are also other reasons behind your Amana washer won’t rinse or spin. 
Using too much detergent. 
Overloading appliance.
Bent or clogged drain hose.
Water pressure is insufficient.
Check these things properly to address any issues with them. Use a recommended detergent and load and clean the clogged drain hose pump regularly.

Why is my Amana washer skipping the rinse cycle?

Your Amana washer may be skipping the rinse cycle mainly if its timer is faulty. So check the timer’s continuity using a multimeter. 
If you notice it has continuity, the timer is OK. If then the washer is skipping the rinse cycle, then check the control board.
It will be the cause of the control board issues.
If the control board is defective, there is no option without changing it.

Final word

It’s really embarrassing if your Amana washer is stuck on the rinse cycle, won’t rinse, or skips it.

But don’t need to worry if you follow our above troubleshooting steps.

Whether you have a top or front-load washer, these troubleshooting steps will help you identify and address common issues. 

If you’ve already tried all the above fixes and the problem persists, contact a professional. Or if you face more issues with your washer, try with Amana washer troubleshooting manual.


Comments

Leave a Reply

Your email address will not be published. Required fields are marked *