Your Amana Washer Sensing Fill Light Blinking normally while the washer is trying to detect the water level in the drum before it starts filling.
But if the light continues to blink for an extended period, there are issues with the water supply, water pressure, or sensors.
There are also possibilities of a clogged drain hose or defective control board.
Anyway, don’t worry about this issue as we’ll explore the possible causes behind this ”sensing fill” blinking error and also give you some quick solutions to try.
What is Sensing Fill Light on Amana Washer
The “Sensing Fill” light on an Amana washer is an indicator that represents the initial phase of the washing cycle.
In this phase, the washer detects the water level in the drum and it occurs before the washer starts filling with water.
During this time, the washer’s sensors measure the load size and check the water level in the drum to determine how much water is needed for the selected wash cycle.
But, If the light continues to blink, there may be issues with the water supply valve, water pressure, sensors, drain hose, or control board.
Why is my Amana washer sensing fill light flashing
Let’s know why your Amana washer sensing fill light flashing and what to do to fix it:
We’ll describe the possible cause behind this problem:
Unbalanced Load
Your washer Sensing Fill light may blink for an unbalanced load.
When the washer load is unevenly distributed in the drum, it tries to balance the load but fails and causes the light to blink.
Pause the cycle, and open the washer door. Then, re-distribute the clothes evenly in the drum.
Finally, resume the cycle.
Water Supply Issues
Insufficient water supply or low water pressure can also cause the Sensing Fill light to blink.
- Check the water supply to the washer is adequate to function properly. Ensure the water faucets are fully open.
- Next, check the drain hoses for any kinks or blockages that might be restricting the water flow.
- Ensure the hose is not positioned too low, causing water to drain out prematurely.
If everything seems fine with the water supply, you can test the water inlet valve to determine if it needs to be replaced.
Faulty Water Inlet Valve
A malfunctioning water inlet valve can prevent the washer from receiving water properly. It will cause the washer to blink the fill light.
Check the water inlet valve for any signs of damage or malfunction. If it is faulty, replace the valve.
Clogged Inlet Valve Screens
If the screens are blocked by debris or sediment, it can restrict the flow of water into the washer. As a result, it leads to delays in filling and the blinking light.
Cleaning the filter screens can help improve water flow and resolve the blinking light issue.
- So, turn off the washer and disconnect it from the power source.
- Access the water inlet valve screens and clean them thoroughly to remove any debris or sediment.
Control Panel Reset
Sometimes, a simple control panel reset can resolve the issue.
- Unplug the washer for a few minutes, then plug it back in and try starting a new cycle.
Faulty Sensor or Control Board
If none of the above solutions work, there may be an issue with the water level sensor or the control board.
The washer’s sensors may not be detecting the water level properly, leading to the blinking light.
- If this is the case, it may be necessary to replace the faulty sensor.
- If the control board is faulty, you should better to contact a professional to repair or replace it.
Amana washer sensing fill then stops
If your Amana washer gets stuck on the Sensing Fill stage and then stops without proceeding further, it could be due to several factors.
Inadequate water supply, improper drain hose positioning, a faulty water inlet valve, control board problems, sensor malfunctions, or a clogged detergent dispenser may cause this problem.
To address this problem, check and ensure proper water supply, drain hose placement, and cleanliness, and consider resetting the washer as we’ve described above earlier.
Final thought
So, don’t panic if your Amana washer sensing fill light flashing. This flashing mainly indicates there are water filling issues that indicate the problem with the water inlet valve, sensor, or water presser issue.
Whatever the reasons, we’ve already explored all the probable reasons and their quick solutions.
Leave a Reply